the copyright and authority for the interpretation of the products are reserved by mornsun specifications subject to change without notice. T1100L a/1-2008 page 1 of 2 passive signal amplifier iin & iout T1100L description product program part number power supply input output isolation power output channels package T1100L none 4-20ma 4-20ma none 1 dip12 electrical characteristics power supply none power dissipation none power supply data power protection none input signal 4 -20ma input impedance voltage drop 250mv(at input signal=20ma) overload 300ma input data voltage drop <3v(20ma) output signal 4 -20ma load 300 at output signal=20ma output data load regulation 0.05% meas.val./100 transmission characteristics offset 0.1%f.s. gain error 0.1%f.s. temperature drift 0.0035%f.s./ c(-25 c to +71 c) isolation characteristics galvanic isolation two-port isolation between input and output isolation voltage 3kvdc (tested for 1minute and 1ma max, humidity < 70%) insulation resistance 100m ,500vdc between input and output other characteristics operation temperature:-25 c to +71 c ambient temperature transport and storage temperature:-50 c to +105 c package sip12 weight about 8g application environment no dusts, gases of fiercely vibration, impulsion or gases that may erode to the components surrounded t1100 series, a standard analog amplifier, with anterior circuit 4-20ma current signal input and posterior 4-20ma current signal output ,is a passive signal isolation module .the series adopt magneto design and high efficiency loop electric-larceny technology ,efficiently reducing the reliance of current signal isolation on the power ,realize 4-20ma standard signal isolation with high accuracy and line regulation. besides, the modules have extremely low temperature drift (no more than 35ppm/ under -25 c to +71 c) .the isolation voltage between the input and output can up to 3kvdc. features two-port isolation between input and output high accuracy (0.1% f.s.) high linearity (0.1% f.s.) isolation voltage(3000vdc/60s) low voltage-drop(at 20ma<3v) extremely low temperature(35ppm/ c) industry standard(operating temperature range:-25 c to 71 c) high reliability(mtbf 500,000 hours) model selection txxxxl isolationamplifier input output power supply isolation power output package style mornsun science & technology co.,ltd. address: 2th floor 6th building, huangzhou industrial district, guangzhou, china tel: 86-20-38601850 fax:86-20- 38601272 http://www.mornsun-power.com note: 1. all specifications measured at ta=25 c, humidity<75%, nominal input voltage and rated output load unless otherwise specified. 2. only typical models listed, specifications of custom product may be different. please contact our service people directly for certain conditions.
the copyright and authority for the interpretation of the products are reserved by mornsun specifications subject to change without notice. T1100L a/1-2008 page 2 of 2 schematic diagram application note iin+ iin- iout+ iout- 12+ 9- 2- 1+ 11+ 10- signalinputsignaloutput application circuit diagram signalinput signaloutput 1. please read instruction book carefully before using the product. if you have any question, please contact with our technical support. 2. please don t install in the dangerous zone. 3. don t divide the product privately in case the equipments ineffective or go wrong. after service 1. products are carefully inspected and controlled before going out from our factory. if they operated abnormally or there were anything wrong in the inner parts, please contact with our agents near you or technical support in our company as soon as possible. 2. 3 years warranty since the delivery date. during the period of quality guarantee our company will repair or change free of charge if product has any quality problem in the process of normally using. application circuits see a guide to instrumentation isolation amplifiers for more detail. packaging size and terminal description 1 2 9 11 12 10 0.50 (0.020) recommended footprint top view,grid:2.54mm(0.1inch) diameter:1.00mm(0.039inch) note: unit:mm(inch) pin section:0.50*0.3mm(0.020*0.012inch) pin section tolerances:0.05mm(0.002inch) general tolerances:0.25mm(0.010inch) first angle projection footprint details (bottom view) pin function input+ input- output- output+ (side view)
|
